PN rating selection for buildings: a general guide with Zoloto examples
Updated 13 Nov 2026 · Reviewed by MTC technical desk
The short answer
A general guide to choosing a PN rating for building water, pump and fire lines: work out the highest pressure including the pump's shut-off and the static head of the building, add the margin your designer sets, then pick the next PN class up. It lists the Zoloto valves at each PN and converts head in metres to bar.
Want prices for these valves? Call 98490 02060 or build a quote list.
The method (general, not Zoloto’s advice)
The method below is general engineering guidance. Zoloto’s documents do not give a selection procedure, only each valve’s ratings. Your designer decides the margin and the code to follow.
- Find the highest pressure the valve can see. That is the pump’s shut-off or maximum pressure, plus the static head of water above the valve, plus any surge your designer allows for. Normal running pressure is not enough.
- Convert head to pressure. About 0.098 bar per metre of water. The table shows common heights.
- Add the margin your designer or the code requires.
- Choose the PN class at or above the result. PN 10, 16, 25 and 40 are the usual steps: see PN rating explained.
- Check the temperature, the flange standard and the mark on the datasheet.
| Head (m of water) | bar | kg/cm² |
|---|---|---|
| 10 | 0.98 | 1.00 |
| 20 | 1.96 | 2.00 |
| 30 | 2.94 | 3.00 |
| 50 | 4.90 | 5.00 |
| 70 | 6.86 | 7.00 |
| 100 | 9.81 | 10.00 |
The conversion uses the standard definition: a column of water 10 m high exerts about 1 kg/cm². Add the pump’s shut-off pressure to it.
Zoloto valves for building water lines, with their ratings
| Fig. | Type | PN in title | Shell test as printed |
|---|---|---|---|
| 1079A | Sluice valve | PN 1.0 | 1.5 MPa |
| 1079B | Sluice valve | PN 1.6 | 2.4 MPa |
| 1083 | Swing non-return valve | PN 1.0 | 1.5 MPa |
| 1083A | Swing non-return valve | PN 1.6 | 2.4 MPa |
| 1084 | Y strainer | PN 10 | 15 kg/cm²g (220 psig) |
| 1084A | Y strainer | PN 16 | 24 kg/cm²g (340 psig) |
| 1082 | Dual plate check valve | PN 16 | 24.50 kg/cm²g (350 psig) |
| 1078B | Butterfly valve | PN 1.6 | 2.4 MPa |
Reading it for a real line
If the highest pressure on a line works out well under 10 bar, a PN 10 or PN 1.0 valve may be enough, subject to your designer’s margin; between 10 and 16 bar look at PN 16 or PN 1.6, such as the sluice valve 1079B (at 100 mm, ₹22,898 as on 26 Sep 2026) and the swing non-return valve 1083A (₹15,402 as on 26 Sep 2026). Above that look at PN 25 (the PN 2.5 butterfly valves of the 1078 series). The next rating up costs more at every size, so do not over-specify, but do not under-specify a line that can see the pump’s shut-off pressure. Zoloto’s Plumbing and Fire Fighting groups list the valves it assigns to building services.
Ask us for today’s price, and see the extras page for add-ons. For the Zoloto valves at each rating see the pressure class pages.
A worked example (general)
Suppose a pump delivers to a tank on a roof 60 m above the pump room. The static head at the pump delivery is about 5.9 bar (60 m times 0.098). If the pump’s shut-off pressure is 4 bar, the pressure at the pump delivery with the line closed is about 9.9 bar, and your designer will add a margin. The valve at the pump then needs a rating above that figure: a PN 16 valve rather than a PN 10, because 9.9 bar leaves no margin under PN 10. The roof valve sees only the pump’s shut-off figure less the height, so it can be a lower class. This example is general guidance with invented numbers, not Zoloto’s advice.
Why the lowest valve is not always the lowest class
The pressure at a valve depends on where it is on the line, not only on the pump. Valves at the bottom of a riser see the static head of everything above them. That is why a long vertical run can need a higher PN at the bottom than at the top, and why a designer may split a tall building into pressure zones with pressure reducing valves.
Zoloto pressure reducing valves used for zoning. MRPs are per piece, as on 26 Sep 2026.
| Fig. | Product | Sizes (mm) | MRP per piece | HSN |
|---|---|---|---|---|
| 1040B | Forged Brass Compact Pressure Reducing Valve (Screwed) | 15–50 | ₹3,087 to ₹12,392 | 84811000 |
| 1040A | Bronze Compact Pressure Reducing Valve (Screwed) | 65–100 | ₹30,957 to ₹95,570 | 84811000 |
Zoloto’s compact pressure reducing valves are listed for water: see the pressure reducing valve guide.
Questions to ask your designer
Ask which code or standard sets the test pressure for the line, whether the pump’s shut-off pressure or its maximum pressure is the one to use, how much margin they want, and whether pressure reducing valves are used to split the building into zones. Write the answers on the order so that we quote the same ratings you specified.
Related guides
Questions
How do I convert metres of water to bar?
Each 10 metres of water head is about 0.98 bar. This is general: 1 bar is about 10.2 metres of head.
Should I use the pump's duty pressure or its shut-off pressure?
Use the higher figure, the shut-off or maximum pressure, because a valve can see it when the line is closed. Your designer sets the margin.
What PN do tall buildings need?
It depends on the height and the pump. The head at the bottom of a tall riser adds to the pump pressure. Ask your designer.
Is this Zoloto's advice?
No. The method is general engineering guidance, labelled as general. Zoloto's documents only give each valve's rating, test pressures and temperature.
What about temperature?
The allowed pressure falls as temperature rises. Zoloto prints a maximum working temperature for most products.
Sources
- Zoloto price list dated 26.09.2026 (pages 2 to 24)
- Zoloto product catalogue, datasheets for the products named
- General engineering guidance (not from Zoloto documents) for the selection method
Zoloto products in this guide

Cast Iron Non Return Valve PN 1.6 (Flanged)
50–300 mm · 9 sizes · ISI
₹6,744 to ₹65,930 as on 26 Sep 2026

Cast Iron Sluice Valve PN 1.6 (Flanged)
50–300 mm · 9 sizes · ISI
₹10,420 to ₹1,08,175 as on 26 Sep 2026

Cast Iron Y-Type Strainer, PN 16 (Flanged)
40–250 mm · 9 sizes
₹4,999 to ₹81,898 as on 26 Sep 2026

Butterfly Valve (Wafer Type), PN 1.6 with S.S 304 Disc
40–150 mm · 7 sizes · ISI
₹3,507 to ₹12,399 as on 26 Sep 2026
Prices are Zoloto's Maximum Retail Prices (MRP) per piece, as printed in the Zoloto price list dated 26 September 2026. Zoloto states that GST at 18% is included in these MRPs. Prices, sizes and availability can change without notice. Call 98490 02060 or email info@maheshvalves.com for today's price and stock before ordering.
Need a price or a quote? Call 98490 02060 or email info@maheshvalves.com.