Valve glossary
Short meanings of the terms you meet in Zoloto's price list and catalogue. Each entry says whether the meaning is general engineering or Zoloto's own usage, and links to the Zoloto products that show it.
A · B · C · D · E · F · G · H · I · K · L · M · N · O · P · Q · R · S · T · U · V
A
- actuator
- An actuator is a device that opens and closes a valve without a hand operating it. It is driven by compressed air, electricity or another source and can respond to a control signal, instead of a lever, gear or handwheel.
- air release valve
- An air release valve is a valve that lets air trapped in a water pipe escape, usually at a high point, and closes again when water reaches it. It uses a float to open and shut a small outlet.
- angle pattern
- An angle pattern valve has its inlet and outlet at a right angle to each other, so it also turns the flow through 90 degrees. A straight pattern valve has them in line. The choice depends on your pipe layout.
- ANSI
- ANSI is the American National Standards Institute. On valve datasheets it appears in the names of older flange and valve standards, such as ANSI B16.5 for flanges, which is now published by ASME. ASA is the institute's former name.
- API 594
- API 594 is an American Petroleum Institute standard for check valves, covering wafer, lug, flanged and butt-welding types. It sets design and dimension rules for those valves. It is not a pressure class.
- API 600
- API 600 is an American Petroleum Institute standard for steel gate valves with flanged or butt-welding ends and a bolted bonnet. It sets design, dimensions and testing rules for those valves, and is not itself a pressure class.
- API 602
- API 602 is an American Petroleum Institute standard for compact forged steel gate, globe and check valves in small sizes. Zoloto's Class 800 valves name it, together with BS EN ISO 15761, as their design standard.
- ASME B16.5
- ASME B16.5 is the American standard for pipe flanges and flanged fittings, giving dimensions, drilling and pressure classes such as Class 150 and Class 300. Flanges to it must match their mating flange to join.
B
- back seat
- A back seat is a seating surface on the stem side of a valve that seals when the valve is fully open. It lets the stem packing be replaced under pressure in some designs. It is not the same as the main seat.
- balancing valve
- A balancing valve is a valve used to set the flow in one branch of a water circuit so every branch gets its share. It is adjusted once during commissioning, and a double regulating type can lock that setting.
- ball (ball valve)
- The ball in a ball valve is the sphere with a hole through it that turns a quarter of a turn to open or close the flow. Its material and finish affect wear and corrosion resistance.
- bar
- A bar is a unit of pressure equal to 100 kilopascals, close to atmospheric pressure. One bar is 0.1 MPa, about 1.02 kg/cm², and about 14.5 psi. Gauge pressure in bar is written bar(g) or barg.
- blow-off valve
- A blow-off valve, on a boiler, is a valve used to drain water and sludge from the boiler to keep the water clean. It is opened for short periods and must close tightly. Its design is regulated for boilers.
- body (valve body)
- The body is the main pressure-containing part of a valve, which holds the flow passage and connects to the pipe. Its material, such as bronze, cast iron or steel, largely sets the valve's rating and service.
- bolted bonnet
- A bolted bonnet is a valve cover held to the body by bolts and a gasket. It is used on larger and higher-pressure valves and can be opened for maintenance. The alternatives are a screwed bonnet and a union bonnet.
- bonnet
- The bonnet is the cover of a valve body, through which the stem passes. It holds the packing that seals the stem. Bonnets are joined to the body by a screw, bolts or a union nut, and the joint decides how easily the valve can be serviced.
- bore
- The bore of a valve is the diameter of its flow passage. A full bore valve has a passage as large as the pipe it joins. A reduced or standard bore valve has a smaller passage, which saves cost and size but restricts the flow somewhat.
- BS 10
- BS 10 is a British Standard for pipe flanges, with lettered tables that fix the flange dimensions and bolt drilling for a range of working pressures. Zoloto's datasheets refer to its Tables F, H and J for flanged valves.
- BS 21
- BS 21 is the British Standard for pipe threads where pressure-tight joints are made on the thread. It covers a tapered external thread and a parallel or tapered internal thread. It is the basis of the BSP and BSPT threads.
- BS 4504
- BS 4504 is a British Standard for circular flanges for pipes, valves and fittings, with flanges designated by PN. Flanges must match their mating flange in drilling and rating to be joined.
- BSP
- BSP stands for British Standard Pipe, a family of pipe threads used on screwed valves and fittings. The two forms are parallel (BSPP) and tapered (BSPT). A thread is named by the nominal pipe size, not its outside diameter.
- BSPT
- BSPT is the tapered form of the British Standard Pipe thread. The thread narrows along its length, so the joint tightens as it is screwed in. It is not interchangeable with a parallel thread or with NPT.
- bucket steam trap
- A bucket steam trap, or inverted bucket trap, removes condensate from a steam line using a bucket that floats and sinks with the amount of steam inside it. It opens and closes a valve as it moves.
- butterfly valve
- A butterfly valve closes with a disc on a spindle that turns a quarter of a turn. It is short and light for its size, and in the wafer form it fits between two pipe flanges.
- bypass
- A bypass is a small passage or pipe that lets fluid go around the main closing element of a valve. On a check valve a bypass arrangement allows a limited flow around the flap. What it is used for depends on the system.
C
- CF8
- CF8 is a cast stainless steel grade, the cast equivalent of S.S 304 wrought stainless steel. It resists corrosion in many services. Zoloto's titles write it as CF8 / S.S 304.
- CF8M
- CF8M is a cast stainless steel grade, the cast equivalent of S.S 316 wrought stainless steel. It contains molybdenum and resists corrosion better than CF8 in many services. Zoloto's titles write it as CF8M / S.S 316.
- check valve
- A check valve, also called a non-return valve or NRV, lets liquid or gas flow in one direction only and closes by itself when the flow tries to reverse. It has no handle, because the flow itself opens and closes it.
- chrome plating
- Chrome plating is a thin layer of chromium deposited on a metal surface to resist wear and corrosion and give a bright finish. On valves it is used on balls, bodies and trim.
- Class 150
- Class 150 is a pressure class designation, from the ASME system, used for flanged valves and flanges. It is a class name, not a pressure in psi: the pressure a Class 150 valve can take depends on its material and temperature.
- Class 800
- Class 800 is a pressure class designation used for small-bore forged steel valves, commonly with screwed or socket weld ends. It is a class name, not a pressure in psi, and the allowed pressure depends on material and temperature.
- condensate
- Condensate is the water formed when steam gives up heat and condenses. In a steam system it collects in pipes and equipment and must be removed, usually by steam traps, without letting the steam escape.
- cover (valve cover)
- On a valve, the cover is the removable part of the body, usually on a check valve, through which the internal parts can be reached. It is the equivalent of a bonnet on a valve with a stem.
- cutaway
- A cutaway is a drawing or model that shows the inside of a valve, with part of the body cut away to show the working parts. It helps people see how the valve is built.
- Cv
- Cv is a valve's flow coefficient in US units: the flow in US gallons per minute of water that gives a pressure drop of 1 psi. Cv is about 1.156 times Kv, the metric equivalent in cubic metres per hour per bar.
D
- dezincification
- Dezincification is a form of corrosion in which zinc is selectively leached out of brass, leaving a weak porous copper structure. It happens in some waters and can cause leaks. Resistant grades exist.
- DIN 2533
- DIN 2533 is a German standard for cast iron and steel pipe flanges rated PN 16, with a defined bolt circle and drilling. A flange made to it only mates with a flange of the same standard.
- DIN 2545
- DIN 2545 is a German standard for steel pipe flanges at PN 40. It sets the flange diameter, bolt circle and drilling for that rating. A flange to it must be matched with another of the same standard.
- disc
- The disc is the closing part of a valve that moves against the seat to stop or allow flow. In a butterfly valve it turns, in a check valve it lifts or swings, and in a globe valve it moves up and down.
- DN
- DN stands for nominal diameter, a size label for pipes and valves written in millimetres, such as DN 25. It is a round number used to match parts, not an exact measurement of any one dimension.
- double regulating valve
- A double regulating valve is a balancing valve with two settings: one to throttle the flow to the value needed, and one to lock that value so the valve can be shut and reopened to the same position.
- drain plug
- A drain plug is a threaded plug at the bottom of a strainer body or cover. Removing it lets trapped dirt and water drain out so the screen can be cleaned without removing the strainer.
- dual plate check valve
- A dual plate check valve has two half-discs hinged on a central pin, which swing shut by spring or flow reversal. It is a wafer valve that fits between two pipe flanges and is shorter and lighter than a swing check valve.
- ductile iron
- Ductile iron, also called S.G. iron or spheroidal graphite iron, is a cast iron alloy in which the carbon is present in spheroidal or nodular form. Zoloto's Special Note 19 says the two names mean the same thing.
E
- end connection
- The end connection is the way a valve joins the pipe: screwed, flanged, socket weld, wafer or another type. It must match the pipe's thread or flange standard, or the valve cannot be fitted.
- EPDM
- EPDM is ethylene propylene diene rubber, a synthetic rubber used for seals and linings. It suits hot water and many chemicals but is not recommended for mineral oils. It is one of several elastomer choices.
- epoxy coating
- Epoxy coating is a hard polymer paint applied to metal to resist corrosion and wear. On valves it is used on iron parts that touch water. Its thickness and approval depend on the product.
- extended stem
- An extended stem is a longer valve stem that lets the operator reach the valve through insulation or from above ground. It adds length but does not change the valve's pressure rating.
F
- face-to-face
- The face-to-face dimension is the length of a flanged valve measured between its two end faces. It must match the space in the pipe, which is why standards fix it for each valve type and size.
- ferrule cock
- A ferrule cock is a small valve screwed into a water main to tap off a branch pipe for a service connection. It has a long inlet that goes into the main and a plug that controls the flow.
- Fig No (article number)
- A figure number, or Fig No, is the catalogue number a manufacturer gives to one product design. Zoloto uses a four-digit number, sometimes with a letter, such as 1035 or 1079B, and each is a different product.
- flange
- A flange is a flat rim on a pipe or valve end with bolt holes, used to join two parts with bolts and a gasket. Its diameter, thickness and drilling are set by a standard.
- flare nut
- A flare nut is a nut that tightens a flared tube end against a seat to make a sealed joint, without threads on the tube. It is common on copper tube and fuel or gas lines.
- FLB brass
- FLB is a grade of forged brass in Indian Standard IS 6912, used for forged valve bodies, stems and glands. It is a leaded brass. The grade code is printed with the standard number.
- forged brass
- Forged brass is brass shaped under pressure from a heated billet instead of being cast. Forging gives a dense, uniform structure and is used for small valves, bib cocks and ball valves.
- forged steel
- Forged steel is steel shaped under pressure from a heated billet. It is stronger and denser than cast steel and is used for compact high-pressure valves, usually Class 800 or above, in small sizes.
- full bore
- A full bore valve has a passage as large as the pipe's internal diameter, so flow is nearly unrestricted. A reduced bore valve has a smaller passage, which is cheaper but causes more pressure loss.
- fusible plug
- A fusible plug is a safety device screwed into a boiler shell. Its core melts at a set temperature if the water level drops too low, letting steam escape to warn the operator.
G
- gate valve
- A gate valve closes by lowering a flat or wedge-shaped gate across the flow. It is meant to be fully open or fully closed, not used to throttle, and gives low flow resistance when open.
- gauge glass (water level gauge)
- A gauge glass is a transparent tube on a boiler or tank that shows the water level. A water level gauge fitting holds the glass and has cocks to isolate it. It is a safety fitting on boilers.
- gear operator
- A gear operator, or gearbox, is a handwheel with reduction gearing fitted to a valve so a person can turn a large or high-torque valve. It is common on big butterfly valves.
- gland
- A gland is the part that presses the packing around a valve stem to stop leakage along it. It is tightened by a gland nut or bolts. Over-tightening it makes the stem hard to turn.
- gland packing
- Gland packing is the soft sealing material compressed around a valve stem by the gland. Common materials include PTFE, graphite and asbestos-free fibres. It wears and can be replaced.
- globe valve
- A globe valve closes with a disc pressed onto a seat in a spherical body. It is suited to regulating flow and gives tight shut-off, but has more flow resistance than a gate valve.
- graphite packing
- Graphite packing is a stem seal made of braided or moulded graphite. It tolerates high temperatures and is used for steam and thermic fluid. It is softer than metal and can abrade a stem if it is not clean.
- gun metal
- Gun metal is a bronze alloy of copper, tin and zinc, traditionally used for valves and fittings because it resists corrosion and wears well. Names vary: it is also sold as leaded tin bronze.
H
- handwheel
- A handwheel is the wheel you turn by hand to open or close a valve. Its size gives leverage, and its material is chosen for strength and grip. Lever and gear types are the alternatives.
- heavy pattern
- Heavy pattern is a valve body weight class that is thicker and stronger than a medium or light pattern. It suits higher pressures. The term is a convention and sizes of each pattern vary by maker.
- HSN code
- An HSN code is the Harmonised System number used in India to classify goods for GST. For valves the heading is 8481. The code must appear on a tax invoice and decides which GST rate applies.
- hydrostatic test
- A hydrostatic test pressurises a valve with water to check its body and seat for leaks and strength. The shell test checks the body, the seat test checks the closure. Test pressures are higher than working pressure.
I
- IBR
- IBR means the Indian Boiler Regulations, the law governing boilers and the steam fittings used on them in India. Valves for boiler service are made and tested to its rules, and a certificate can be issued.
- IBR Form III C
- IBR Form III C is a test certificate issued under the Indian Boiler Regulations for certain boiler fittings, recording that they passed a prescribed test. Buyers often ask for it with I.B.R marked valves.
- inside screw
- Inside screw, or IS, means the stem thread is inside the valve body, in contact with the fluid. The stem may rise or not rise. The alternative is outside screw, where the thread is outside the body.
- integral seat
- An integral seat is a seat machined as part of the valve body, not a separate ring. It cannot be replaced alone. A renewable seat ring can be replaced and is common on steam valves.
- IS 13095
- IS 13095 is the Indian Standard for butterfly valves for general purposes. It sets design, dimensions, marking and tests for them. It corresponds to the European EN 593.
- IS 14846
- IS 14846 is the Indian Standard for sluice valves for water works purposes. It sets design, dimensions, marking and testing for the cast iron sluice valves used in water supply networks.
- IS 1538
- IS 1538 is an Indian Standard for cast iron fittings for pressure pipes for water, gas and sewage. It is cited in Indian valve datasheets for flange dimensions and drilling where flanges are cast iron.
- IS 2692
- IS 2692 is the Indian Standard for ferrules for water services. It covers the small fitting that taps a branch pipe off a water main and sets its dimensions and materials.
- IS 318
- IS 318 is the Indian Standard for leaded tin bronze ingots and castings. Grade LTB 2 is a common one for valve bodies. A grade code tells you the alloy, not the valve's quality.
- IS 5290
- IS 5290 is the Indian Standard for landing valves, the hydrant valves fitted on fire fighting risers. It sets the design, connection sizes and testing for them.
- IS 5312
- IS 5312 is the Indian Standard for reflux (non-return) valves, the swing type. It sets design, dimensions and testing for those check valves.
- IS 554
- IS 554 is the Indian Standard for pipe threads where pressure-tight joints are made on the threads. It is the Indian equivalent of ISO 7 and BS 21, which match its thread form.
- IS 6912
- IS 6912 is the Indian Standard for copper alloy forgings, including forged brass. Grade FLB is the leaded forged brass commonly used for valve stems, glands and small bodies.
- IS 778
- IS 778 is the Indian Standard for copper alloy gate, globe and check valves for water works purposes. Valves marked to it carry the ISI mark when the maker holds a licence.
- ISI mark
- The ISI mark is the Bureau of Indian Standards certification mark shown on a product made under a BIS licence to an Indian Standard. A valve may follow a standard without carrying the mark.
- ISO 17292
- ISO 17292 is an international standard for metal ball valves for petroleum, petrochemical and allied industries. It sets design, dimensions and tests. BS 5351 was its British predecessor.
K
- kg/cm²g
- Kg/cm²g is a pressure unit meaning kilograms-force per square centimetre, gauge. It is about 0.98 bar and is common on older Indian specifications. The g means it is measured above atmospheric pressure.
- Kv
- Kv is a flow coefficient: the flow in cubic metres per hour of water at 15 degrees Celsius that gives a pressure drop of one bar across a valve. A higher Kv means less resistance. Cv is its US equivalent.
L
- landing valve
- A landing valve is the hydrant outlet valve on a fire fighting riser, fitted at each floor with an instantaneous coupling for a fire hose. Indian design rules for it are set by IS 5290.
- lever
- A lever is a handle that turns a quarter-turn valve between open and closed, usually through ninety degrees. Its position along the pipe shows whether the valve is open or shut.
- lift check valve
- A lift check valve has a disc or piston that lifts off its seat when flow passes and drops back when it stops. It suits horizontal lines and gives a tight seal, but has more flow resistance than a swing check.
- limit switch
- A limit switch is a switch that signals when a valve has reached fully open or fully closed. It is fitted to an actuator so a control system can know the valve's position.
- lining
- A lining is a layer of rubber or polymer inside a valve body that acts as the seat and seal and protects the metal from the fluid. In butterfly valves the lining is bonded into the body.
- lock shield
- A lock shield is a cap or cover over a valve's adjusting spindle that stops casual tampering, so a setting made by an installer stays put. It is common on balancing and radiator valves.
- LTB2
- LTB 2 is a grade of leaded tin bronze in IS 318, the Indian Standard for leaded tin bronze ingots and castings. Zoloto writes it IS 318 Gr. LTB 2 or LTB2. The grade names the alloy, not the finished valve.
M
- magnet insert
- A magnet insert is a magnet fitted inside a strainer or valve to catch iron particles from the fluid. It is an optional extra on some strainers, not a standard part of a valve.
- medium pattern
- Medium pattern is a valve body weight class between light and heavy pattern, rated for moderate pressures. The term is a convention, and the actual wall thickness depends on the maker and standard.
- metal-to-metal seat
- A metal-to-metal seat is one where a metal disc seals against a metal seat, with no soft insert. It tolerates heat and wear but may leak slightly. A soft seat gives a tighter shut-off at lower temperature.
- MOC
- MOC stands for material of construction: the list of materials a valve's parts are made from, such as body, disc, stem and seals. Datasheets present it as a numbered parts table.
- MPa
- MPa, megapascal, is a metric pressure unit equal to one million pascals, or 10 bar. Pressure ratings such as PN 1.6 are sometimes written in MPa, so 1.6 MPa equals 16 bar.
- MRP
- MRP is the maximum retail price printed on a manufacturer's price list. A seller may charge less. In Zoloto's list it is per piece and includes GST at 18%, with extras for options priced separately.
N
- needle valve
- A needle valve has a slender tapered plunger that fits a small seat, for fine control of low flows. It is used on instrument lines and gauges and is usually made in small sizes.
- nitrile
- Nitrile rubber, or NBR, is a synthetic rubber that resists oils and fuels. It is used for seals, O-rings and valve linings in water and oil service, but is not suited to strong oxidisers or very hot water.
- non-return valve
- A non-return valve, also called an NRV, check valve or reflux valve, lets fluid flow one way and closes on its own if flow reverses. It protects pumps and lines from backflow and needs no operator.
- non-rising stem
- On a non-rising stem valve the stem only turns and does not move up or down, so the valve needs little headroom. The gate travels along the stem. It is common on buried or tight installations.
- NPT
- NPT is National Pipe Taper, the American tapered pipe thread standard, which differs from British BSPT in thread angle and pitch. The two do not mate properly, so the thread on your pipe must be known.
O
- O-ring
- An O-ring is a ring-shaped rubber seal that sits in a groove to stop leaks between parts. Valves use it on stems and bonnets. The rubber type must suit the fluid and temperature.
- OS&Y
- OS&Y means outside screw and yoke. The stem thread sits outside the valve, in a yoke, away from the fluid, and the stem rises as the valve opens. It is the usual design for steam, oil and fire service.
P
- padlock
- A padlock provision is a hole or tab on a valve handle that lets the valve be locked open or closed, to prevent tampering. It is common on isolation valves in fire and process lines.
- parallel slide valve
- A parallel slide valve has two parallel discs with a spreader between them that closes against flat seats. It is used for steam and boiler blow-off service because it seals well under pressure.
- perforated screen
- A perforated screen is a metal sheet with small round holes, used as the filter element in a strainer. The hole diameter sets which particles pass. It is cleaned or replaced when it clogs.
- PN
- PN is a European pressure rating label meaning nominal pressure in bar, such as PN 10 or PN 16. It is a class label and not a test pressure, and permitted pressure falls as temperature rises.
- pneumatic actuator
- A pneumatic actuator uses compressed air to move a valve, usually through a piston or diaphragm. It can be double acting, driven by air both ways, or spring return. It needs an air supply.
- pressure reducing valve
- A pressure reducing valve, or PRV, lowers a higher inlet pressure to a steadier lower outlet pressure. It works on its own using a spring and diaphragm and protects pipes and fittings downstream.
- psig
- Psig is pounds per square inch gauge, a pressure unit measured above atmospheric pressure. One psig is about 0.069 bar. It is used on American-style specifications and appears beside kg/cm²g on many Zoloto datasheets.
- PTFE
- PTFE, polytetrafluoroethylene, is a slippery plastic that resists many chemicals and heat. Valves use it for seats, seals and gland packing. It can creep under load, so design limits apply.
Q
- quarter-turn
- A quarter-turn valve opens or closes with a ninety degree turn of the handle. Ball and butterfly valves are quarter-turn types. They work fast, but fast closing can cause water hammer.
R
- raised face
- A raised face is a flange facing with a raised ring around the bore where the gasket sits, so the bolts concentrate pressure on the gasket. It is the usual facing on Class 150 flanges.
- reduced bore
- A reduced bore valve has a passage one size smaller than the pipe. It is cheaper and lighter than full bore, but flow loss is higher, and it is not suited to pigging.
- relief valve
- A relief valve opens by spring force when pressure rises above a set value, and closes again when it falls. It protects a system against overpressure. Open and enclosed discharge are two designs.
- rising stem
- On a rising stem valve the stem moves up as the valve opens, so you can see from the stem whether it is open or shut. It needs headroom and is common on gate and globe valves.
S
- safety valve
- A safety valve opens fully when pressure exceeds its set point to release steam or fluid quickly, protecting a boiler or vessel. A relief valve opens gradually. Boiler safety valves are regulated.
- screwed end
- A screwed end is a valve end with an internal or external thread that screws onto the pipe. It is used on smaller sizes. The thread type, such as BSPT or NPT, must match the pipe.
- seat
- The seat is the surface inside a valve against which the closing part presses to stop flow. It can be part of the body or a separate ring, and may be metal or soft material.
- seat ring
- A seat ring is a separate ring fitted into a valve body that forms the seat. It can be replaced when worn, unlike a seat machined into the body. Steam valves often use renewable rings.
- seat test
- A seat test checks that a closed valve does not leak across its seat. Water or air pressure is applied on one side. The seat test pressure is normally lower than the shell test pressure.
- SG iron
- SG iron, spheroidal graphite iron, is cast iron treated so the graphite forms spheres, which makes it stronger and tougher than grey cast iron. It is also called ductile iron or nodular iron.
- shell test
- A shell test applies water pressure to the assembled valve body, with the valve partly open, to check the casting and joints for leaks. It is done at about one and a half times the rated pressure.
- sluice valve
- A sluice valve is a gate valve used on water supply and drainage lines, usually cast iron with a flanged end and a non-rising or rising stem. Indian rules for it are in IS 14846.
- socket weld
- A socket weld end has a recess into which the pipe is inserted and fillet welded. It is common on small forged steel valves in high-pressure lines, and gives a strong leak-free joint.
- solenoid valve
- A solenoid valve is opened or closed by an electromagnet when current is applied. It is used for automatic on-off control of liquids and gases, mainly in small sizes.
- solid wedge
- A solid wedge is a one-piece wedge-shaped gate in a gate valve that seats against the angled body seats. It is simple and strong. A flexible or split wedge allows for some distortion.
- spindle
- The spindle is another name for a valve's stem, the rod that moves the closing part. Some makers use spindle for the part on gate valves and stem for others. The word has no separate technical meaning.
- spring-loaded
- A spring-loaded valve uses a spring to hold the closing part on its seat. It opens when fluid force exceeds the spring force. Relief valves, check valves and pressure reducing valves use springs.
- SS304
- SS304, or Type 304, is a common austenitic stainless steel with about 18 percent chromium and 8 percent nickel. It resists corrosion in many waters but is not suited to chlorides in hot service.
- SS316
- SS316, or Type 316, is an austenitic stainless steel with added molybdenum, which gives better resistance to chlorides and acids than SS304. It costs more.
- SS410
- SS410, or Type 410, is a martensitic 13 percent chromium stainless steel that can be hardened. It is used for stems and seats because it resists wear, but it resists corrosion less than 304.
- steam stop valve
- A steam stop valve is a globe valve designed for steam, with a rising stem, heat-resistant seats and packing. It isolates a steam line or boiler outlet and is usually marked for boiler use.
- steam trap
- A steam trap is a valve that lets condensed water and air out of a steam system while holding the steam in. It improves heating efficiency. Types include thermodynamic, inverted bucket and thermostatic.
- stellite
- Stellite is a hard cobalt chromium alloy welded on to valve seats and discs to resist wear, erosion and heat. It is used in steam and high-pressure valves.
- stem
- The stem is the rod that connects the handwheel or actuator to the closing part and moves it. It passes through the packing, so its finish and straightness matter for sealing.
- strainer
- A strainer is a fitting that catches dirt in a pipe using a screen, to protect pumps, meters and valves downstream. A Y-type strainer has a slanted screen chamber and is easy to clean.
- swing check valve
- A swing check valve has a hinged disc that swings open with flow and shuts under gravity and back pressure. It gives low resistance and suits larger pipes, but can slam if flow reverses quickly.
T
- test cock
- A test cock is a small tap on a valve body used to connect a gauge or take a sample. On balancing valves test cocks on each side of the orifice let the pressure drop be measured.
- thermic fluid
- Thermic fluid, or heat transfer oil, is a high-temperature oil circulated in closed heaters at low pressure. Valves for it must hold up at high temperature and not leak oil.
- thermodynamic trap
- A thermodynamic steam trap has one moving disc that closes when steam flashing past it lowers the pressure above it, and opens for cooler condensate. It is compact and suits small steam lines.
- three-piece ball valve
- A three-piece ball valve has a centre body and two end pieces held by bolts, so the centre can be removed for service without taking the pipe apart. It costs more than a two-piece valve.
- two-piece ball valve
- A two-piece ball valve has a body and an end cap screwed together, with the ball held between them. It is cheaper than a three-piece type, but the pipe must be unscrewed to service it.
U
- union bonnet
- A union bonnet is a valve cover held to the body by a large union nut, so it can be opened quickly by hand or wrench. It is used on small bronze globe and gate valves.
V
- Viton
- Viton is a brand of fluoroelastomer rubber with good resistance to heat, oils and many chemicals. It is used for seals and linings where EPDM or nitrile would fail, and costs more.
See also the frequently asked questions, the guides and browse by type.